I was very careful when changing the drives, and I did not experience any problems. If the pins within the socket become bent, or loose, then all sorts of problems can manifest. How well this docking station performs and its reliability very much depends upon the IDE connection and the reliability of the socket. I had some very old Western Digital drives from the year 2000 and one drive gave me problems however, I doubt anyone will be using a drive as old as that today.Īlthough some of the sellers are describing the operation of this docking station as "plug and play hot-swappable", it is better to power down the drive and docking station before changing it, otherwise you could end up inflicting serious damage to the drive electronics. Almost all drive manufacturers follow the same design standards, consequently the IDE and power sockets are usually in the same place, and fit properly with their respective plug counterparts on the docking station. The majority of the ones I used were old and smaller capacity, however they seemed to work fine. Unfortunately I only have info from the 871 - 876 All in 1 HDD docking stations, but will endeavour to find out more info on the other models.Working in IT, I had many drives I could test. It will tell you if it is compatible with USB3. See table below the download links for more info on your specific model of all in 1 HDD docking station. Question All in 1 HDD Docking Station Not Seen. This applies to any electrical device - the voltage has to be correct +/- 5% but the Ampage can be much higher and won't harm your device as long as it at least the minimum required to turn on your electronic device. I have lost my cd driver for All in 1 HDD docking 876c, just wondering if i can download a copy somewhere Sort by date Sort by votes mickypheonix Honorable. The device may light up, but won't work and the PSU will get hot and eventually fail. The Amps can be anything because the device will only draw what it needs, so if it is 12v and 3A/4A/5A then it's fine, but if the current (Amps) is too low, it will still try and draw what it needs from the power supply and this will cause problems. So another thing to try before sending your All in 1 HDD Docking Station back to your supplier is to try a higher rated PSU. Follow the steps to uninstall & reinstall the USB Universal Serial bus host controller from device manager. I misplaced my power supply and tried a 12v 1A supply which I thought came with the docking station but it didn't read drives, so i used a 12v 3A power supply, plugged it into the rear of the PC (not a hub) and hey presto. Let the Windows install the generic drivers and then see if it helps you to fix the issue. I'm not sure if the power supply is rated at a high enough Ampage for all in 1 HDD docking stations listed here. I have tested a later SATA WD drive and they work fine. Just a side note for those that have an IDE WD drive and you can't access it - Western Digital IDE drives are NOT compatible. However, there is the possibility it may not work with USB3 ports depending on your model so bear these in mind. If your All-in-1 docking station is not recognised when you plug it in, then you have another problem, I have now tested the 875 on Windows 10 and it works just fine. Please note - Drivers for the All in 1 HDD docking station listed on this page are not needed in order for the docking station to be recognised by your PC/Laptop if you use the following OS's: Compatible with SATA I, SATA II, SATA II transfer rate up to 3Gb/s All in One HDD Docking Drivers Windows 98, SE (Driver required) Windows 2000, ME Windows XP (max 2 TB) Windows Vista Windows 7 and Windows 8 (max above 3. Features XD/CF/TF/SD/MS card reader and eSATA port High Speed USB 2.0 up to 480Mbps data transfer rates (USB 1.1 Backwards compatible) Supports all 2.5"/3.5" SATA/IDE Hard Disk Drive of any capacity up to 2TB (Not WD IDE) FREE Dropbox online storage - click here All in 1 HDD Docking station Features
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |